Cart 0

BSA Electronics Intellisplit™ - Intelligent Splitter Indoor version

  • 59999
  • Save $ 3000

The NEW hardwired version of our popular Dryer Buddy™ Plus AUTO is here!

The BSA Electronics Intellisplit™ - Intelligent Splitter Indoor version is a hardwired fully automatic 2-way switcher based on the original Dryer Buddy™ Plus AUTO. It allows you to share your dryer outlet with your EVSE without having to flip any switches. It may also be used to share any circuit with a second load, for example an Electric Water Heater circuit can be shared with a new 240v outlet for anything you need to power. Basic operation is simple, the Dryer circuit is always live and the EVSE circuit is only live when there is enough amperage available to charge your EV. When the Dryer is off it is drawing little to no amps so the EVSE circuit is switched on allowing your EV to charge. If the Dryer is turned on at any time then the EVSE circuit is switched off, when the Dryer is done, power is restored to the EVSE circuit and if your EV needs charging it will resume charging after a 5 min delay (adjustable). Designed so other members of the house don't have to understand anything technical to use the Dryer when they need to do a load of laundry.

This unit is built in the same high quality polycarbonate case as the Dryer Buddy™  Plus AUTO and I use a beautiful indoor rated kWh meter to display important information. This keeps track of how much Energy you are using so you know how much $ in electricity you’ve used, by simple multiplying the value by your utilities rate (0.13/kWh here in Vegas) The meter is wired to read system Voltage and only meter the Current flowing through the EVSE outlet, unlike the original Dryer Buddy where the meter reads all Current flowing through the unit. In this configuration the Kilowatt Hours (kWh's) will only accumulate for Energy flowing through the EVSE outlet (on the right of the face) this value is stored between power outages and may be reset when you like. This allows you to see only the Energy your Electric vehicle has consumed.

The BSA Electronics Intellisplit™ - Intelligent Splitter Indoor version has an entry hole on the bottom for 3/4" conduit. You may increase the hole size with a stepper bit and/or add additional holes for your installation needs. This unit is for indoor use and is not Outdoor rated, it must be located inside a building protected from the elements. For our Outdoor version see here; 
BSA Electronics Intellisplit™

Selecting models; Typically you would select the BSA Electronics Intellisplit with the same rating as your existing circuit breaker 30 or 50 amps, but you can future proof by ordering a larger unit that has more bandwidth (in amps) so that you may upgrade the cable from your breaker panel in the future or take the unit with you to a new location with a 50 amp circuit.

This is a kit that requires home electrical installations skills or installation by a qualified Handyman/Electrician. Dimensions are: 10.00 x 7.00 x 4.06 in / 254.00 x 177.80 x 103.12 mm

Please note: What needs and doesn't need to be permitted as well as local code vary from city to city, you will want to look into this before purchasing and committing. BSA Electronics is not responsible for these additional cost and returns are not accepted if it is determined you cannot use this custom built product in your project.

Some high efficiency Dryers such as the Bosch Series 800 Max slowly ramp the speed of the motor and don't draw significant current while running, which will cause erratic switching, to alleviate this the Delay Controller is standard in the BSA Electronics Intellisplit. If you are using a BSA Electronics Intellisplit™ to share one circuit and charge two EV’s (no Dryer) then you will definitely need the built in Delay Controller.

The BSA Electronics Intellisplit™ - Intelligent Splitter Indoor version is similar in operation to the Outdoor version, but the Indoor version has a kWh meter and no redundant circuit breaker on the EVSE output. Have a look at the Demo video;

 URL link: BSA Electronics Intellisplit™

Need some help identifying your wall outlet? We can help! Below is a description of the more common NEMA outlets and their numbers as well as some handy NEMA plug charts. You can also email us a pic of your plugs and outlets you need help identifying and we would be happy to help.

Here are the more common NEMA outlets:

  • 5-15 standard 15A 120 volt household outlet, the most common you see everywhere.
  • 5-20 standard 20A 120 volt household outlet, required by code in bathroom and behind your refrigerator.
  • 6-15 standard 15A 240 volt household outlet, found in homes and motels for running in-wall Air Conditioners, it’s the smaller brother to the NEMA 6-20 outlet. The 5-20 is not as common as a 6-20 outlet with it’s “T” shaped slot as it will accept both 6-20 and 6-15 plugs.
  • 6-20 standard 20A 240 volt household outlet, found in homes and motels for running in-wall Air Conditioners, also found occasionally in residential garages.
  • 6-50 standard 50A 240 volt 3-prong outlet, found in shops and garages used for large welders.
  • 10-30 standard 30A 240 volt 3-prong Dryer outlet found in homes build before 1996
  • 14-30 standard 30A 240 volt 4-prong Dryer outlet found in homes build in 1996 and newer
  • 14-50 standard 50A 240 volt 4-prong Range (electric stove top) outlet, also called RV-50 at the RV parks. By far the best universal connector to have for an EVSE. This is the one the Tesla guys install in their garages.
  • TT-30 (Travel Trailer 30amp) 30A 240 volt 3-prong outlet, the older style found in RV parks, not used in residential homes.
  • L6-30 (locking 240 volt 30amp) Twist-Lock 30A 240 volt outlet, my personal favorite locking connector, easy to find in stores, works great for adding adapters to portables EVSE’s equipped with a L6-30 plug.

220/240 volt outlets are commonly install with the ground pin towards the ceiling for safety. 110/120 volt outlets can be found mounted in all directions. Be sure to carefully look at your outlet and the chart, it's easy to mistake one outlet for another if your outlet has it's ground pin facing the floor instead of the ceiling or Vice Versa compared to the chart.

In the full NEMA number you will see a capital R or P. The R stands for Receptacle (outlet) and the P stands for Plug, we commonly truncate this to just the numbers and add the word receptacle (or outlet) at the end. For example 14-50R becomes 14-50 receptacle or 14-50 outlet.

Need some extra length between your outlet and your Electric Vehicle Charging Station (EVSE)? I custom build extension cords to the length your need and with the plug and outlet of your choice, see my extensions in the Adapter’s section for several models; Extension Cords

Email me with your custom request

Quick Sheet Manual: BSA Electronics Intellisplit™ - Intelligent Splitter

Customer Reviews

Based on 4 reviews Write a review

We Also Recommend

Customer Reviews

Based on 4 reviews Write a review